Pump Fed Systems require careful consideration of available utilities and on-site plumbing.

Use our Planning Tools to get started and Contact Us when you’re ready to talk.

Air-activated Zone Control Kit solenoids receive a compressed air signal from the controller to activate the flow of compressed air and chemical solution to the foggers.

When fogging is finished, a Bleed Tank Assembly keeps the air line open momentarily to clear residual chemical solution from fogger heads to prevent dripping after the solution flow is deactivated.

Pre-diluted (or ready-to-use) chemical can be pumped from any tank, or diluted on demand with a water-driven dosing proportioner (Dosatron, Mix-Rite, etc.)

1. Pump Fed Fogger Selection
2. Zone Control Kit
3. Metered Bleed Assembly
4. Chemical Dilution, Pumping, and Control Mechanisms
   • Chemical Source Considerations
   • Controller Type (Single vs. Multi-Zone)

Part numbers below link to full product details on the main Lafferty website.

Pump Fed Foggers receive ready-to-use chemical solution from a central pump system. Compressed air atomizes the chemical solution and projects damp or dry chemical mist in 1, 2, 3, 4 or 8 directions.

Choose a model based on the desired coverage and compressed air availability. Contact us if you require a configuration that is not listed.

950011	633 1-Way Pump Fed Fogger
950013	633 2-Way Pump Fed Fogger
950014	633 4-Way Pump Fed Fogger
950018	633 8-Way Pump Fed Fogger
**********	**********
950111	305 1-Way Pump Fed Fogger
950112	305 2-Way Pump Fed Fogger
950114	305 4-Way Pump Fed Fogger
950118	305 8-Way Pump Fed Fogger –Shown above–
**********	**********
950211	455 1-Way Pump Fed Fogger
950214	455 4-Way Pump Fed Fogger
950218	455 8-Way Pump Fed Fogger

Pump Fed Fogger Zone Control Kits are used in conjunction with a PLC Vision Controller to operate Pump Fed Foggers in multiple zones.

Air-activated solenoids receive a compressed air signal from the controller (sold separately) to regulate the flow of compressed air and chemical solution to the foggers.  

The included Bleed Tank Assembly keeps the air line open momentarily to clear residual chemical solution from fogger heads to prevent dripping after the solution flow is deactivated.

950850	Pump Fed Fogger Zone Control Kit –Shown above—
950850SS	Pump Fed Fogger Zone Control Kit W/ SS Solenoids

The Metered Bleed Assembly provides a controlled relief outlet for pressure from chemical gasses and related dripping when fogging with off-gassing chemicals (for example, peracetic acid).

Each fogger zone should be equipped with a Metered Bleed Assembly. It should be installed downstream of the in-line Pump Fed Fogger Zone Control Kit.

950852

Pump Fed Fogger Metered Bleed Assembly

Chemical Source

1. Dilute chemical on demand with a Level Master and/or pump ready-to-use chemical solution to foggers using FPS Chemical Feed System. Shown below.
2. Dilute chemical with a water-driven dosing proportioner (Dosatron, Mix-Rite, etc.) mounted to a Dosing Panel. Shown above.

Regardless of dilution method, the typical chemical solution pressure delivered to foggers is 10-20 PSI.

989304	Level Master (No Tank)
709170	7-Gallon Tank With Suction Stem —Other tank sizes available—
919045	FPS Fogger Chemical Feed System
**********	**********
909900	Single Dosing Panel (Injector NOT Included)

Controller Type

Choose a controller based on the number of zones, desired programming ability, and maximum air CFM rating.

Pump Fed Fogger Zone Control Kits are required to receive a pilot air signal from the Controller (see Zone Control Kits above).

Multi-Zone Controllers

Single Zone Controllers

• Simple timers with optional recycling and delay functions.
• A solenoid controls airflow to activate foggers simultaneously.
• PLC Jazz models offer more flexible programming options.

NOTE: Single zone controllers are ideal for Venturi Fogger setups where only a few foggers are involved. Multi-zone arrangements are far more common for Pump Fed Foggers.

950800	Fogger Single Cycle Controller – 180 CFM
950802	Fogger Single Cycle Controller – 460 CFM
950810	Fogger Recycling On / Off Controller – 180 CFM
950812	Fogger Recycling On / Off Controller – 460 CFM
950820	Fogger Delayed Start, Single Cycle Controller – 180 CFM
950822	Fogger Delayed Start, Single Cycle Controller – 460 CFM
**********	**********
950830	Fogger PLC Jazz Controller – 180 CFM
950832	Fogger PLC Jazz Controller – 460 CFM