Overview
Requirements
Chemical Concentrate |
---|
Water | |
---|---|
Temperature | up to 160°F |
Pressure | 35 to 125 PSI |
Flow | 9.9 GPM @ 40 PSI |
Supply Line | 3/4" |
Hose | 3/4" ID x 10' |
Overview
Safety & Operational Precautions
To Install (refer to diagram on next page)
If you are connecting to a potable water supply follow all local codes for backflow prevention.
Set the chemical dilution ratio by threading one of the color coded metering tips into chemical check valve. See chemical label for dilution ratio recommendation or consult your chemical supplier.
* For stronger no tip concentration to be achieved order and install the optional dual pick up kit. See chart.
*This will also allow 2 different chemicals to be blended. Mix and match metering tips in the standard and optional second pick up assemblies to obtain ratios that are not possible using a single tip.
To Operate
WITH OPTIONAL TRIGGER GUN
WITH OPTIONAL DISCHARGE BALL VALVE
Metering Tip Selection | |||
---|---|---|---|
Metering Tip Color |
OZ/MIN |
Dilution Ratio | |
985835 | Dual Pick-up (No tip) | ||
Brown | 0.56 | 2263:1 | 9.3:1 |
Clear | 0.88 | 1440:1 | 9.2:1 |
Bright Purple | 1.38 | 918:1 | 9.2:1 |
White | 2.15 | 589:1 | 9.2:1 |
Pink | 2.93 | 432:1 | 9.1:1 |
Corn Yellow | 3.84 | 330:1 | 9.0:1 |
Dark Green | 4.88 | 260:1 | 9.0:1 |
Orange | 5.77 | 220:1 | 8.9:1 |
Gray | 6.01 | 211:1 | 8.9:1 |
Light Green | 7.01 | 181:1 | 8.8:1 |
Med. Green | 8.06 | 157:1 | 8.8:1 |
Clear Pink | 9.43 | 134:1 | 8.7:1 |
Yellow Green | 11.50 | 110:1 | 8.6:1 |
Burgundy | 11.93 | 106:1 | 8.6:1 |
Pale Pink | 13.87 | 91:1 | 8.4:1 |
Light Blue | 15.14 | 84:1 | 8.4:1 |
Dark Purple | 17.88 | 71:1 | 8.2:1 |
Navy Blue | 25.36 | 50:1 | 7.8:1 |
Clear Aqua | 28.60 | 44:1 | 7.7:1 |
Black | 50.00 | 25:1 | 6.8:1 |
No Tip Ratio Up To: | 9.3:1 | 4.7:1 | |
The dilution ratios above are approximate values. Due to chemical viscosity, actual dilution ratios may vary. | |||
Formula | |||
GPM × 128 ÷ Desired Dilution Ratio = oz/min
|
Unit Flow Rates | |
---|---|
PSI | GPM |
35 | 9.26 |
40 | 9.90 |
50 | 11.07 |
60 | 12.12 |
70 | 13.10 |
80 | 14.00 |
90 | 14.85 |
100 | 15.65 |
110 | 16.42 |
120 | 17.15 |
125 | 17.50 |
Troubleshooting Guide |
---|
Problem | Possible Cause / Solution | |
---|---|---|
Startup | Maintenance | |
A) Unit will not draw chemical. B) Dilution too weak. C) Dilution too strong D) Water backing up into chemical container. | 1, 2, 3, 6 4 5 |
7, 8, 9, 10, 11, 12 11 8 |
Possible Cause / Solution | |
---|---|
Startup | Maintenance |
|
|
PREVENTIVE MAINTENANCE: When the unit will be out of service for extended periods, place chemical tube(s) in water and flush the chemical out of the unit to help prevent chemical from drying out and causing build-up. Periodically check and clean chemical strainer and replace if missing. |